|
|
| Fluon®LM-ETFE is a new fluororesin
which combines the excellent properties in heat resistance and other
mechanical properties owned by ETFE resin and the low melting point.
|
| Features and advantages of
Fluon®LM-ETFE |
- The melting point is lower by 30-40deg.C compared to that of
the conventional ETFE resin.
- Film with excellent transparency can be produced.
- Processing can be performed in a wide temperature range.
|
| Basic properties of Fluon®LM-ETFE |
| In addition to the mechanical properties similar to
that owned by the conventional ETFE, Fluon® LM-ETFE shows original
features in the melting point, thermal decomposition, flame resistance
and flexibility. |
| terms |
standard |
unit |
LM-720AP |
LM-730AP |
LM-740AP |
ETFE (C-88AXP) |
| Melt
Flow Rate |
ASTM D3159
(297ºC, 49N) |
g/10min |
10-20 |
20-30 |
30-40 |
12 |
| Specific
gravity |
ASTM
D792 |
- |
1.78 |
1.74 |
| Melting
point |
DSC |
deg.C |
225 |
260 |
| 10%weight
loss |
TGA |
deg.C |
410 |
390 |
| Oxygen
index |
ASTM
D2863 |
% |
40 |
31 |
| Flame
retardant |
UL94 |
- |
V-0 |
V-0 |
| Tensile
strength |
ASTM
D638 |
MPa |
43 |
40 |
38 |
46 |
| Elongation |
ASTM
D638 |
% |
380 |
400 |
420 |
430 |
| Heat
aging (1) |
ASTM
D638 |
% |
90 |
88 |
88 |
85 |
| Heat
aging (2) |
ASTM
D638 |
% |
120 |
120 |
117 |
110 |
| Anti
cracking at 200deg.C |
ASTM
D1693 |
- |
excellent |
good |
| Flexural
modulus |
ASTM
D790 |
MPa |
647 |
882 |
| Dielectric
constant |
ASTM
D150 |
103Hz |
- |
2.4 |
2.5 |
| 106Hz |
- |
2.4 |
2.5 |
Dielectric
tangent
(tanδ)
|
ASTM
D150 |
103Hz |
- |
0.0007 |
0.0007 |
| 106Hz |
- |
0.0082 |
0.0080 |
|
*after 200deg.C 96hrs
(1) retention of tensile strength
(2) retention of elongation |
| Grade |
Filler |
Process |
| LM-720AP |
none |
General
injection and extrusion molding |
| LM-730AP |
none |
General
injection and extrusion molding |
| LM-740AP |
none |
General
injection and extrusion molding |
|
| * |
Before use of this product, we urge the careful reading
of the appropriate Material Safety Data Sheet (MSDS). Technical information
brochures are available for some products. For the safe use of the
product, one must abide by the use method and the purposes described
in the relevant brochure and MSDS. Please note that the brochure and
MSDS are based on the latest information and data available, but additional
and/or corrections may be made, from time to time, without notice
when new data becomes available and/or regulations are changed.
|
|
(C)Copyright ASAHI GLASS CO.,LTD 2005-2007. All Rights Reserved. 
